AUTOMOBILE TESTERS FOR IGNITION COIL/ MOTOR/ SENSOR SIGNAL/ ECU IG80/MNB-2/QDB-2

Description

AUTOMOBILE TESTERS FOR IGNITION COIL/ MOTOR/ SENSOR SIGNAL/ ECU IG80/MNB-2/QDB-2
Video will open in a new window
Using the eBay App? Paste link into a browser window:
[isdntekvideo]
Automobile Ignition Coil Detector Tester Natural Gas 24V Gasoline 12V Ignition
Video will open in a new window
Using the eBay App? Paste link into a browser window:
[isdntekvideo]
Automotive Sensor Signal Analog Box Auto Signal Generator Computer Repair Detection Simulation Tool IG80/MNB-2/QBD-2 Motor Fault Detector
(Fast Shipping)
Description:
Simulation MNB-2 main functions
High power wire-wound potentiometer is used to protect the output interface from over-current short circuit
Voltage sensor signal simulation test
V1 and V2 output and voltage ratio can be adjusted arbitrarily
Air flow meter, inlet pressure sensor, oil pressure sensor, supercharging pressure sensor common rail pressure sensor, oxygen sensor manual/automatic simulation (0.1v-0.9v)
Throttle pedal sensor dual signal (most 2:1) ratio can be arbitrarily adjusted throttle position sensor, air conditioning pressure sensor (voltage type)
Resistance type sensor signal simulation test
Coolant temperature sensor, inlet temperature sensor, oil temperature sensor exhaust temperature sensor, fuel temperature sensor, evaporator temperature sensor environmental temperature sensor, etc
Voltmeter function: measuring range 3v-30v
Separate LED test lights (kit)
Sensor 5V power supply
Voltmeter function
Can be used as a voltmeter, measuring voltage range 3-30V Before measuring voltage, rotate V1 and V2 knob to the right to the end
Then measure again, otherwise the measured voltage will not be accurate!
Special signal generator for automobile
Main functions:
Crankshaft position sensor signals:
Various common missing gear signals of crankshaft position sensors are stored internally, including 58+2 (60-2), 58+1,57+2,57+ 1, 37+1,36+2, 35+1, 34+2, 22+1 a standard missing gear signal 60+0
The above signals can be selected magnetoelectric or Hall output
The standard 60+0 signal also simulates a speed (odometer)
Sensor for detecting and maintaining odometer
Analog ABS sensor, photoelectric sensor signal, etc
At any frequency greater than 2Hz, 10 kinds of signals can be output by pressing the SET button, among which 60-0 is standard magnetoelectric or Hall signal, and the other 9 kinds are magnetoelectric or Hall missing tooth signal (crankshaft position sensor signal).
Segmenting the output frequency
1. Turn the frequency knob left to the bottom to display 2Hz on the screen
2. Press the SET button
Screen display 01, frequency range 2-1000Hz
The screen shows 02, frequency range 2-2000h
Screen displays 08, frequency range 2-8000Hz0
9,10,11, frequency range 0.2-102hz
QBD2,Motor actuator fault detector:
B: Drive test ignition coil includes independent ignition, packet ignition, coil type and module type
2. Driving test fuel injectors: including 12V fuel vehicle for Gasoline and 12V 24V fuel tor for diesel Vehicle
3.Drive and test various duty cycle control Solenoid monitoring, fuel metering, etc
4.Drive and test various duty cycle control Motors, carrying pump motors, etc
Meanwhile, the paper is driving and testing idle stepping motor, headlamp following stepping motor, etc
The hall signal with adjustable output frequency, amplitude and duty cycle is used to simulate 7. Various duty cycle sensors, such as air conditioning pressure sensor (duty cycle),Air Flow Meter (Duty Cycle), etc
B: Yes, it does. Power supply voltage range: 12V-24V, with reverse connection protection, overcurrent protection
8. Driving current range of electromagnetic coils: 0-3.3a
9. The Output frequency range: 1 hz - 100 KHZ
10. Duty cycle adjustment: 1%-100%
11. Adjustable voltage: 1.25 V to 11.5 V
QBD-2 Auto actuator fault detector
Step motor drive test
The main stepper motors used in automobiles are: instrument stepper motor, idle stepper motor, headlamp follow - up steering and headlamp height adjustment
Stepper motors and other stepper motors are composed of two sets of coils, namely group A coil and Group B coil
Step of testing stepper motor:
1. Supply power to drivbao and the voltage shall not exceed 12V
2. Use the multimeter to measure the two sets of coils of the stepping motor, then connect AA and BB of the driver respectively, press the stepping motor button, the stepping motor should turn normally, if it doesn't turn, the stepping motor has a fault
Description of electromagnetic coil drive test
Fuel injector, solenoid valve, small motor controlled by duty ratio, ignition coil (coil type) and other internal principles are equivalent to a solenoid coil, with two wiring terminals. Firstly, the accessories to be driven for drivbao are 12V, and the accessories to be driven are 24V, and drivbao is 24V.The coil first received at the end of the drive of the power supply voltage output pin, then adjust output frequency to 10 hz or so, if the electromagnetic valves, electronic throttle, small motor, frequency adjustment and 50-100 hz, the duty ratio to 1%, and the other end connects to the electromagnetic coil drive socket, driven parts should be able to work at this time, if you don't work, can increase duty ratios can not work, well illustrated
Hall signal usage Instructions (Hall signal frequency, signal amplitude and duty cycle can be adjusted)
The hall signal output current is small, so the coil cannot be driven directly. Only when the tested accessories are integrated with a drive module, can the Hall signal be driven.
For example: modular ignition coil, modular motor
The driver module generally has three wiring, namely: power +, ground -, and signal input terminal
To drive power supply (12 v or 24 v), if the power of the tested module below 12 v adjustable voltage output pin, if it is 12 v or 24 v direct supply voltage output pin, the ground connected and then adjust the frequency to 10 hz - 200 hz, duty ratio to 99% (hall signal output socket is negative duty ratio signal), adjustable voltage signal amplitude (hall) adjusted to 5-11 v, then the module signal end socket connection, and drive the treasure hall signal measured module should be able to work at this point if you can't work, reduce the duty ratio,
The IG80 supports 12V ignition coil detection
Coil type: two wire, three wire
Modular: three wire, four wire
Group ignition, independent ignition
Support 24V natural gas ignition coil detection, coil type, intelligent type
IG80 auto ignition coil detector
A new generation of vehicle ignition diagram detection equipment
Support the common 12V gasoline car ignition coil detection
Support the market common 12V, 24V natural gas ignition coil detection
The instrument is easy to operate and only needs three steps:
1. The fire coil of the measured point and the detector shall be connected according to the instructions
2. Plug the instrument into the external power supply, and if the ignition coil is 12V, connect the 12V electro-sink ignition coil is 24V, then connect the 24V power supply
3. Press the key to start the ignition coil. If you want to test the ignition coil's working condition at various rotating speeds, adjust the rotating speed knob
Warm tips :
1. Import duties/VAT: Please check with your country\'s customs office to determine what these additional costs will be prior to bidding buying.
2. Import duties, VAT, Taxes and Charges are not included in the item price or shipping charges. These charges are the buyer\'s responsibility.
3. So if sent by express delivery such as DHL EMS SF TNT FEDEX ,you might need to pay the tax for your country .
SHIPPING
Items will be shipped out within 3-5 business days by
International AirMail with Tracking
after the payment is cleared by PayPal.The arrival time depends on your location.
This time may get longer due to special holidays and various clearances of the customs on both sides. Delivery time usually will be 14-35 business days. If you didn't receive your package within this time schedule, please do not hesitate to contact us.
PAYMENT
​We accept payments only via Paypal.
We will ship to ebay's address only. Please make sure your address on ebay is the same as your shipping address before you pay.
RETURNS / EXCHANGES / REPLACEMENTS
All items will be checked carefully and packaged in good condition.But if the product is defective or damaged upon arrival, please contact us immediately.
Returns accepted within 30 days of delivery date and item must be in original new condition, not worn or altered in any way with attached tags & wrap. Otherwise the deal is final. Return shipping must be paid by the buyer.
CUSTOMER SERVICE
Our goal is to provide high quality products for a good competitive value, backed by excellent customer service.
We will be happy to resolve any issues you may have in a cordial and friendly manner.we will try our best to solve any dispute and try our best to satisfy you. If you are not satisfied with our product, please contact us first.
Integrity is of prime importance to us. We will leave Positive Feedback as soon as the transaction has been completed.
CONTACT US
Feel free to contact us if you have any questions. Your positive feedback is highly appreciated. Please let us know before leaving any negative feedback.
Please give us the opportunity to resolve any problems.Please contact us via eBay for any comments, questions or suggestions that you may have,
We will be happy to assist you.